Double Heat Sink

Revision as of 04:34, 21 March 2018 by BrokenMnemonic (talk | contribs)

Description

Double Heat Sinks, often abbreviated DHS and colloquially also referred to as Freezers throughout the Inner Sphere after their NAIS codename[1], operate in much the same way and for the same purpose as standard heat sinks. The difference is that a double heat sink offers twice the heat dissipation capacity of a standard heat sink, for the same mass (one ton).

Their drawback is that they are much bulkier than a standard heat sink (unless integrated into a fusion engine).
The advanced Clan version is twice the size of a standard heat sink; Star League era double heat sinks and those later (re-)developed by the Inner Sphere are three times as bulky as a standard heat sink.

Also, double heat sinks are normally incompatible with standard heat sinks. A given unit must therefore be equipped exclusively with either standard or double heat sinks, though exceptions are known.[2]

The benefits of doubled heat dissipation capacity usually outweigh the drawbacks and by 3058 almost every 'Mech model was equipped or retrofitted with double heat sinks.

History

Introduced in 2567 by the Terran Hegemony[3], double heat sinks were commonly available during the Star League era but became Lostech over the course of the Succession Wars. Although the technology was essentially extinct after 2865[3] and standard (single) heat sinks became the norm as they were the only ones still available, double heat sinks remained in use in some individual cases.

By the early 31st century, double heat sink technology was on the verge of rediscovery. The Federated Suns had a double heat sink project in its prototype stages by 3022 with individual samples built into operative BattleMechs, and in 3030, towards the end of the Fourth Succession War, the Capellan Confederation already fielded their BJ-3 Blackjack variant[4], the first regular 'Mech design sporting double heat sinks in decades if not centuries. (Although it is not generally known, the Confederation did not develop double heat sinks themselves; the Federated Suns had prototypes manufactured in the Lyran Commonwealth and a Capellan agent was able to siphon a share of the production off to the Confederation.[5])

Following the discovery of the Helm Memory Core and the subsequent dissemination of lost Star League knowledge throughout the Inner Sphere in 3028, double heat sinks gradually became a staple of 'Mech construction again and were extensively used in retrofits and new designs. The NAIS had double heat sinks ready for serial production in 3041.[1][4]

Non-standard subtypes

Besides the normal Star League era double heat sinks used throughout the Inner Sphere and the advanced Clan version, a number of experimental or prototype technologies existed at various times with slightly different capabilities. However, it should be noted that none of these proved viable for mass production or deployment.

Prototype Double Heat Sinks

The prototype Double Heat Sinks developed in the closing years of the Age of War and in the period between the discovery of the Helm Memory Core and the reintroduction of the standard Double Heat Sink shared almost identical characteristics with each other. Functionally, these prototypes were identical to standard Double Heat Sinks, with the following exceptions: firstly, prototype Double Heat Sinks couldn't be mounted in engines.[6][7] Secondly, the prototype Double Heat Sinks in use in the mid-Thirty-first century could be combined with single heat sinks when used in BattleMechs,[7] while the prototype Double Heat Sinks in use during the Reunification War could be combined with single heat sinks in any combat unit that could mount double heat sinks.[6]

Double-Strength Heat Sinks

Relying on corrosive liquid metal coolants instead of advanced radiators for efficiency, Double-Strength Heat Sinks were developed by the Federated Suns near the end of the Third Succession War at the Friden Aerospace Park research installation on Hoff as part of Project Phoenix. Unlike regular double heat sinks, they could be combined with standard heat sinks at leisure and were actually used as refit kits, replacing individual regular heat sinks. In this, they were plainly superior to regular double heat sinks, sharing none of their drawbacks.[8] (It remains unclear whether or not they could be mounted in the engine.) However, they were too brittle and hard to maintain for more than a few years' worth of function.

When the Draconis Combine invaded Hoff in 3022, some 'Mechs among the defenders were equipped with functional prototypes of this type but they are believed to have been destroyed in the fighting. As far as can be determined, neither the Federated Suns nor the Draconis Combine ever used these exact same Double-Strength Heat Sinks again after the battles on Hoff.

Following the sacking of their facility at Hoff, the Federated Suns found they lacked the industrial capacity to resume production of the prototypes. They approached various Lyran Commonwealth firms to build components which were brought together at Hesperus II where Kincaid Defiance Industries assembled them and secretly shipped them to New Avalon from ca. 3026 onwards.[5] The Capellan Confederation obtained a share of these prototypes through an agent.[5]

Corrosive Coolant Experimental Double Heat Sinks

In the late 3030s, the nascent Federated Commonwealth deployed another kind of experimental double heat sinks with corrosive liquid metal coolants. Obviously developed from the prototypes deployed on Hoff, they could also be combined with regular heat sinks but could not be mounted in the engine, and were three times as big (although still had the same mass)[4][9]. Like their predecessors, maintenance problems meant they decayed within only a few years and were unsuitable for widespread deployment, although they did give the Federated Commonwealth a brief advantage in its early days.[3]

References

  1. 1.0 1.1 20 Year Update, p. 72, "Military Technology Review"
  2. The Super Griffin and field refits using suitable prototype double heat sinks have been known to combine regular and double heat sinks
  3. 3.0 3.1 3.2 Starterbook: Sword and Dragon, p. 57, "Double Heat Sinks"
  4. 4.0 4.1 4.2 Historical: War of 3039, pp. 144-145, "Rules Annex - Double Heat Sinks (Freezers)"
  5. 5.0 5.1 5.2 See BattleCorps short story Proprietary, p.??[citation needed]
  6. 6.0 6.1 Historical: Reunification War, p. 179, "Double Heat Sinks (DHS-P)"
  7. 7.0 7.1 Historical: War of 3039, p. 144, "Double Heat Sinks (Freezers)"
  8. Tales of the Black Widow Company, pp. 40-42, 47, "Battle For Hoff Scenario II-III/Battle For Hoff Scenario IV"
  9. Starterbook: Sword and Dragon, p. 58, "Prototype Weapons And Equipment Table"

Bibliography