Difference between revisions of "Eisenfaust"

m
Line 1: Line 1:
 +
{{Update Needed|[[Experimental Technical Readout: Primitives, Volume 3]]}}
 
{{InfoBoxBattleMech
 
{{InfoBoxBattleMech
 
|image=Eisenfaust.jpg
 
|image=Eisenfaust.jpg
Line 23: Line 24:
  
 
==Description==
 
==Description==
The '''''Eisenfaust''''' was originally designed shortly after the [[Lyran Commonwealth]] began building 'Mechs. Based on their experience with the ''[[Commando]]'' and ''[[Ymir]]'', the LCAF tried to build a medium class "seige engine" 'Mech. Though the trials looked promising, the battlefield performance of the early ''Eisenfaust'' was poor and the design was cancelled.
+
The '''''Eisenfaust''''' was originally designed shortly after the [[Lyran Commonwealth]] began building 'Mechs. Based on their experie
 
 
After the recovery of [[lostech]] and advanced [[SLDF]] technologies, Defiance Industries looked at the early ''Eisenfaust'' design again. The updated ''Eisenfaust'' entered production after simulations showed it could be an effective battlefield unit if equipped with updated technologies. In fact the ''Eisenfaust'' was one of the first designs to enter production after the start of the [[Jihad]].<ref>''Technical Readout: 3085'', p. 74</ref>
 
 
 
The updated ''Eisenfaust'' uses an [[XL Engine]] to provide power. The small weight of the engine allows the 'Mech to carry more armor and weaponry than the prototype models, as well as increasing the top speed. More importantly, the use of fifteen [[double heat sink]]s allows the ''Eisenfaust'' to dissipate the heat from all its weapons.
 
 
 
==Armament==
 
The ''Eisenfaust'' uses a single Plasma Rifle as its main weapon. Equipped with two tons of ammunition the rifle can inflict serious damage on any battlefield unit and can obliterate conventional infantry platoons. The ''Eisenfaust's'' slow top speed makes it difficult for the 'Mech to break contact and reload its Plasma Rifle magazine. Therefore Defiance engineers installed a suite of lasers to provide the backup weapons the 'Mech needs to deal with determined opponents. The lasers obviously don't require ammunition, and the Medium Pulse Lasers are effective at targeting battle armor and other "small" threats. The ER Large Laser supports the Plasma Rifle at range, allowing the pilot to save the Plasma Rifle for a knock-out punch.
 
 
 
==Variants==
 
* EFT-4J - This ''Eisenfaust'' model was the original prototype. Though several were produced, Defiance Industries only used them to test weapons and equipment configurations for the EFT-7X. These models remain on [[Hesperus II]] to serve as test vehicles.<ref>''Technical Readout: 3085'', p. 74</ref> BV (2.0) = 977<ref>''Record Sheets: 3085 Unabridged - The Cutting Edge'', p. 110</ref>
 
 
 
* EFT-8X - This variant is a test-bed for some [[Experimental Technology|experimental weapons]]. Removing the standard weapons load of the ''Eisenfaust'' allows engineers to install a [[Binary Laser Cannon]] and some [[Medium Variable Speed Pulse Laser]]s. As this is an experimental model, no other details are known.<ref>''Technical Readout: 3085'', p. 74</ref> BV (2.0) = 1,039<ref>''Record Sheets: 3085 Unabridged - The Cutting Edge'', p. 112</ref>
 
 
 
==Note==
 
The Eisenfaust was released by Defiance Industries in 2515. However, the 'Mech factories that would become [[Defiance Industries]] were founded in 2577 by the [[Lyran Commonwealth]] and the [[Star League]], tough some 'Mech factories have been on Hesperus II prior the [[Star League]]. Those factories were the property of the [[Terran Hegemony ]] rather than the [[Lyran Commonwealth]].
 
 
 
==BattleMech Gallery==
 
<gallery>
 
Image:Mecheisenfaust-5s.jpg
 
</gallery>
 
 
 
==References==
 
<references />
 
==Bibliography==
 
* ''[[Mechwarrior: Age of Destruction]]''
 
* ''[[Record Sheets: 3085 Unabridged - The Cutting Edge]]''
 
* ''[[Technical Readout: 3085]]''
 
 
 
[[Category:BattleMechs]]
 
[[Category:Medium BattleMechs]]
 
[[Category:Lyran Commonwealth BattleMechs]]
 

Revision as of 11:12, 5 November 2012

Eisenfaust
Eisenfaust
Production information
Manufacturer Defiance Industries
Production Year 2515[1]
Model EFT-7X
Class Medium
Technical specifications
Mass 45 tons
Chassis Chariot Type II-B[2]
Armor Durallex Medium
Engine 180 XL
Speed 64 km/h
Jump Jets None
Armament

BV (2.0) 1,203[3]


Description

The Eisenfaust was originally designed shortly after the Lyran Commonwealth began building 'Mechs. Based on their experie

  1. MUL online date for the Eisenfaust
  2. Technical Readout: 3085, p. 74
  3. Technical Readout: 3085, p. 75